Pipes
Source SS 348H Pipe from India
RFQ should define outside diameter / NPS, schedule or wall thickness, seamless or welded route, end preparation, length and testing.
Open SS 348H Pipe sourcing page →Deep specialist metal desk
Metals / Austenitic & High-Alloy Stainless Steel
Source SS 348H from India
India Supply Solutions identifies and qualifies Indian manufacturers and stock sources for Stainless Steel 348H against buyer-approved product form, standard, dimensions, quantity and inspection requirements. We are a procurement and sourcing partner — not the mill or manufacturer. Ready-stock access is live-confirmed through our Indian stockist and manufacturer network by exact form, make, heat / MTC, dimensions, quantity and dispatch status.
UNS S34809
Grade-led technical sourcingGrade sourcing framework
Stainless Steel 348H sourcing
Use this grade hub to select the required product form, governing product standard, dimensions, manufacturing route, heat treatment, traceability, test plan and certification level before supplier comparison.
Typical application areas for this material family include process equipment, food and beverage, chemical service, heat-resistant service, fabrication and general corrosion-resistant engineering. Actual suitability is determined by the buyer's engineering specification; India Supply Solutions does not substitute grades without written approval.
Material gradeStainless Steel 348H
Commercial designationSS 348H
FamilyAustenitic & High-Alloy Stainless Steel
UNS / designationS34809
Product forms
SS 348H products buyers commonly source
Each form has its own technical brief with form-specific RFQ decisions, inspection controls and qualification evidence.
Tubes
Source SS 348H Tube from India
RFQ should define OD, wall thickness, tolerance, seamless or welded route, finish, length, heat treatment and testing.
Open SS 348H Tube sourcing page →Bars & Rods
Source SS 348H Bar / Rod from India
RFQ should define diameter or section, round / hex / flat form, tolerance, condition, heat treatment, length and surface finish.
Open SS 348H Bar / Rod sourcing page →Plates & Sheets
Source SS 348H Plate / Sheet from India
RFQ should define thickness, width, length, finish, flatness, heat treatment and required test certificates.
Open SS 348H Plate / Sheet sourcing page →Coils & Strips
Source SS 348H Coil / Strip from India
RFQ should define thickness, width, coil ID / OD, finish, edge condition, temper and packing.
Open SS 348H Coil / Strip sourcing page →Flanges
Source SS 348H Flange from India
RFQ should define type, nominal size, pressure class, facing, drilling standard, dimensions, heat treatment and marking.
Open SS 348H Flange sourcing page →Pipe Fittings
Source SS 348H Pipe Fitting from India
RFQ should define fitting type, size, schedule / class, end connection, dimensions, manufacturing route and testing.
Open SS 348H Pipe Fitting sourcing page →Fasteners
Source SS 348H Fastener from India
RFQ should define bolt / nut / stud / screw / washer type, diameter, thread, length, property requirement, finish and test documentation.
Open SS 348H Fastener sourcing page →Wire & Mesh
Source SS 348H Wire / Mesh from India
RFQ should define wire diameter, mesh count / aperture, weave, finish, coil / sheet size and mechanical requirement.
Open SS 348H Wire / Mesh sourcing page →Forgings
Source SS 348H Forging from India
RFQ should define drawing or geometry, forging route, heat treatment, machining allowance, mechanical testing, NDT and documentation.
Open SS 348H Forging sourcing page →Instrumentation Tube Fittings
Source SS 348H Instrumentation Tube Fitting from India
RFQ should define tube OD, fitting configuration, thread type, pressure / temperature requirement, material certificate and leak / pressure testing as specified.
Open SS 348H Instrumentation Tube Fitting sourcing page →Manufacturer qualification
How we qualify a SS 348H supplier
1. Grade evidence
MTC / heat identification and grade traceability are checked against the purchase requirement.
2. Product capability
Manufacturer capability is matched to the exact form, dimensions, route, heat treatment and standard.
3. Inspection plan
Dimensional, visual, PMI / chemistry verification, mechanical or NDT checks are defined where applicable.
4. Documents
Required test certificates, inspection records, packing list and export documents are agreed before dispatch.
5. No substitution
No grade, material, route or standard substitution is accepted without written buyer approval.
6. Commercial transparency
Supplier offers are compared on the same approved technical basis.