Pipes
Source Nitronic 60 / Alloy 218 Pipe from India
RFQ should define outside diameter / NPS, schedule or wall thickness, seamless or welded route, end preparation, length and testing.
Open Nitronic 60 / Alloy 218 Pipe sourcing page →Deep specialist metal desk
Metals / Austenitic & High-Alloy Stainless Steel
Source Nitronic 60 / Alloy 218 from India
India Supply Solutions identifies and qualifies Indian manufacturers and stock sources for Nitronic 60 Stainless Steel against buyer-approved product form, standard, dimensions, quantity and inspection requirements. We are a procurement and sourcing partner — not the mill or manufacturer. Ready-stock access is live-confirmed through our Indian stockist and manufacturer network by exact form, make, heat / MTC, dimensions, quantity and dispatch status.
UNS S21800
Grade-led technical sourcingGrade sourcing framework
Nitronic 60 Stainless Steel sourcing
Use this grade hub to select the required product form, governing product standard, dimensions, manufacturing route, heat treatment, traceability, test plan and certification level before supplier comparison.
Typical application areas for this material family include process equipment, food and beverage, chemical service, heat-resistant service, fabrication and general corrosion-resistant engineering. Actual suitability is determined by the buyer's engineering specification; India Supply Solutions does not substitute grades without written approval.
Material gradeNitronic 60 Stainless Steel
Commercial designationNitronic 60 / Alloy 218
FamilyAustenitic & High-Alloy Stainless Steel
UNS / designationS21800
Product forms
Nitronic 60 / Alloy 218 products buyers commonly source
Each form has its own technical brief with form-specific RFQ decisions, inspection controls and qualification evidence.
Tubes
Source Nitronic 60 / Alloy 218 Tube from India
RFQ should define OD, wall thickness, tolerance, seamless or welded route, finish, length, heat treatment and testing.
Open Nitronic 60 / Alloy 218 Tube sourcing page →Bars & Rods
Source Nitronic 60 / Alloy 218 Bar / Rod from India
RFQ should define diameter or section, round / hex / flat form, tolerance, condition, heat treatment, length and surface finish.
Open Nitronic 60 / Alloy 218 Bar / Rod sourcing page →Plates & Sheets
Source Nitronic 60 / Alloy 218 Plate / Sheet from India
RFQ should define thickness, width, length, finish, flatness, heat treatment and required test certificates.
Open Nitronic 60 / Alloy 218 Plate / Sheet sourcing page →Coils & Strips
Source Nitronic 60 / Alloy 218 Coil / Strip from India
RFQ should define thickness, width, coil ID / OD, finish, edge condition, temper and packing.
Open Nitronic 60 / Alloy 218 Coil / Strip sourcing page →Flanges
Source Nitronic 60 / Alloy 218 Flange from India
RFQ should define type, nominal size, pressure class, facing, drilling standard, dimensions, heat treatment and marking.
Open Nitronic 60 / Alloy 218 Flange sourcing page →Pipe Fittings
Source Nitronic 60 / Alloy 218 Pipe Fitting from India
RFQ should define fitting type, size, schedule / class, end connection, dimensions, manufacturing route and testing.
Open Nitronic 60 / Alloy 218 Pipe Fitting sourcing page →Fasteners
Source Nitronic 60 / Alloy 218 Fastener from India
RFQ should define bolt / nut / stud / screw / washer type, diameter, thread, length, property requirement, finish and test documentation.
Open Nitronic 60 / Alloy 218 Fastener sourcing page →Wire & Mesh
Source Nitronic 60 / Alloy 218 Wire / Mesh from India
RFQ should define wire diameter, mesh count / aperture, weave, finish, coil / sheet size and mechanical requirement.
Open Nitronic 60 / Alloy 218 Wire / Mesh sourcing page →Forgings
Source Nitronic 60 / Alloy 218 Forging from India
RFQ should define drawing or geometry, forging route, heat treatment, machining allowance, mechanical testing, NDT and documentation.
Open Nitronic 60 / Alloy 218 Forging sourcing page →Instrumentation Tube Fittings
Source Nitronic 60 / Alloy 218 Instrumentation Tube Fitting from India
RFQ should define tube OD, fitting configuration, thread type, pressure / temperature requirement, material certificate and leak / pressure testing as specified.
Open Nitronic 60 / Alloy 218 Instrumentation Tube Fitting sourcing page →Manufacturer qualification
How we qualify a Nitronic 60 / Alloy 218 supplier
1. Grade evidence
MTC / heat identification and grade traceability are checked against the purchase requirement.
2. Product capability
Manufacturer capability is matched to the exact form, dimensions, route, heat treatment and standard.
3. Inspection plan
Dimensional, visual, PMI / chemistry verification, mechanical or NDT checks are defined where applicable.
4. Documents
Required test certificates, inspection records, packing list and export documents are agreed before dispatch.
5. No substitution
No grade, material, route or standard substitution is accepted without written buyer approval.
6. Commercial transparency
Supplier offers are compared on the same approved technical basis.
RFQ checklist
Request Nitronic 60 / Alloy 218
Send product form, grade / UNS, applicable standard, dimensions, quantity, destination, inspection / testing requirement and delivery target. If you only know the grade, we will help structure the RFQ.
Send RFQWhatsAppRelated grades